What're your thoughts about How to Install a Bathtub Yourself?
Installing a bath tub isn't exactly brain surgery, however it does call for strong plumbing, woodworking, as well as occasionally, tiling skills. Changing an old tub with a brand-new one is also a reasonably challenging job. If the old bathtub is readily obtainable, the project can relocate speedily; if you need to open up a wall to eliminate the old bathtub and also position the new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will need an assistant to leave the old tub and set in the brand-new one. See to it you have certified yourself for the job and also are comfortable trying it. As opposed to hiring a contractor to take control of a halfway-completed project, it is much better to think about utilizing one before you begin. Chances are you may require a specialist plumber to make tube links.
This short article will certainly assist you set up a new bathtub in your washroom if you have actually already purchased a brand-new bathtub as well as don't require to alter the plan of your previous water system pipes.
Your tools and product checklist should make up the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is separate the water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be quite problematic due to the restricted accessibility that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipelines have been eliminated, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a link to the existent supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in area in between the tap and the sink. Protect the faucet in position with the maker given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap adapters. The former kind ought to be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Using the two wood boards under its feet, place the bath tub in the required placement. The wood boards are useful in uniformly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the tub up until the level checks out degree.
To install faucets, fit all-time low of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Turn on the water and also check all joints and new pipework for leaks and also tighten them if needed. Fill the bathtub and also examine the overflow outlet and the regular electrical outlet for leakages.
Lastly, deal with the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the bath tub ought to wait till the tub has been made use of at least when as this will resolve it right into its final setting.
Getting ready for the Installation
To start with, the sustaining structure supplied with the bath should be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to prevent stress on the bath tub.
Fit the versatile tap connectors to the bottom of both taps utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split an inflexible seal, triggering the water to permeate the wall in between the bathroom and the tiling, resulting in problems with moisture and feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can break relatively very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the market. It is recommended to fit the ceramic tiles making use of water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you liked our topic on A Step-by-Step Guide to Installing a Bathtub. Many thanks for spending some time to read through our blog. Liked our article? Please share it. Let another person check it out. I thank you for reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Certified solutions offered.